YardSolver app iconYardSolver is now an app —Get it on Google Play· iPhone app coming soon
YardSolver
Know what you need. Buy exactly that.

Drip Irrigation Calculator

Step 1 · Type your numbers Step 2 · See your answer Step 3 · Print your list

Drip systems fail on arithmetic, not enthusiasm: too many emitters on one line and the far plants get a trickle; run times guessed and beds swing between dust and swamp. This calculator does the three sums that size a system — how many emitters, how much flow the zone draws, and how long to run it to deliver the water you actually intend.

 

Not sure how much water the crop wants? The Watering Schedule Calculator works out weekly inches by crop, stage and weather — bring its per-session depth back here. Depths and per-plant gallons are targets you set; this page turns them into hardware and minutes.

How to use this calculator

  1. Choose plants mode (individual emitters at each plant) or line mode (emitter line through a bed).
  2. Enter the layout: plant count and emitters per plant, or line length, spacing and bed width.
  3. Pick the emitter flow rate printed on your emitters or drip line.
  4. Set the watering target — gallons per plant, or inches of depth — and read emitters, zone flow and run time.

How the maths works: emitters on a line = line length ÷ spacing (plus one for the start of the line). Zone flow = emitters × emitter rate. Run time = water to apply ÷ zone flow. The quiet trap is the mainline limit: a standard ½-inch drip mainline carries about 200 gal/hr before friction starves the far end, so this page counts zones for you when a layout outgrows one line. The full drip planning guide covers layout, pressure and the jug test that verifies it all.

What are you using this for?

Tell us what you are making, and we will help you do it yourself. Type your project below and we will show you the full method, step by step, using the estimate you just made.

A worked example

Twenty tomato plants, 2 emitters each at 1 gal/hr: 40 emitters, 40 gal/hr of zone flow. At 1 gallon per plant per session the system delivers 20 gallons — a 30-minute run. The same garden on drip line instead: 50 ft of line at 12-inch spacing is 51 emitters; applying ½ inch over a 50 × 4 ft bed takes 62 gallons and about 73 minutes. Same water, two honest ways to count it.

Keep going

Set the watering target first with the Watering Schedule Calculator — crop, growth stage, temperature and soil turned into inches per week. Building the system? The drip set-up guide walks the header assembly and layout, and the Rain Barrel Calculator sizes storage if the drip runs off a barrel.

Questions people ask

How many emitters does one plant need?
Vegetables: usually 2, one each side of the stem, so the root zone wets evenly as it grows. Shrubs: 2–4 in a ring. Trees: a ring of 4 or more that moves outward as the canopy grows. One emitter at the stem wets a column, not a root zone — the commonest drip mistake.

What happens if my zone flow is over 200 gal/hr?
The mainline cannot carry it: pressure and flow sag along the line, near emitters hog water and far emitters dribble. Split the layout into zones that run one at a time — this calculator tells you how many — or step up to a ¾-inch mainline for the trunk run.

Why is my run time longer than my neighbour's for the same bed?
Flow rate. A 0.5 gal/hr emitter takes four times as long as a 2 gal/hr emitter to deliver the same water. Slow emitters are not worse — on clay they are better, because the soil can absorb water as fast as it arrives instead of puddling.

Drip line or individual emitters — which is better?
Beds of rows (lettuce, beans, carrots) suit emitter line: even spacing, nothing to place. Widely spaced plants (tomatoes, shrubs, fruit) suit individual emitters you can count and move per plant. Most real gardens end up with both, on separate zones.

How do I know the far emitter really delivers its rating?
The jug test: catch one minute of flow from the first and last emitter in a measuring jug. If the last one is more than about 10% slower, the line is over-long or over-loaded — shorten runs, split the zone, or raise run time to match the slow end.